Rihac IP4200 Manual de Instruções

Premium Continuous Ink Supply Systems. Instruction Manual For Canon Printers IP4200, IP5200 MP800 & MP830 MP500, MP530

104) Preparing your ink reservoirs a) Carefully remove the small travel plugs on the CISS, leaving the filler plug in place. b) Using the

11 THE FOLLOWING STEPS ARE VERY IMPORTANT FOR ALL CANON PRINTERS. 5) Inserting the silicone nozzle seals. a) Remove the printer head from your p

12e) Incorrectly placed silicone seals can cause poor printing quality. Please ensure that the silicone seals do not move from position when insert

137) Tube set up (IP Series Only) a) Remove the backing to the double sided tape and attach the metal tube support arm approximately 6cm from the

14d) Peel off the backing tape to the tube connection and place it as pictured below. Once again please ensure not to twist or bend the tubing.

158) Tube set up (MP800 and MP830 only) a) Using a Phillips head screwdriver, remove the plastic cartridge bay sealing cover from the scanner lid.

16 e) Run the tubing as per the following exiting through the front of the printer. Please refer to section 11) Finishing Touches on 22

179) Tube set up (MP500 ONLY) a) Attach the two black clips as pictured below. The clips have a piece of double sided tape attached, simply remov

18e) Close the scanner lid and check that the ink flow will not be restricted by the lid. Please note after the installation of the CISS the printer

1910) Tube set up (MP530 only) a) Feed the cartridges into the printer through the scanner lid swing arm (as depicted below) and click the cartrid

2

20c) Attach tubing holder clip at the following point d) Attach the large raiser clips to the left and right side of the printer case. This allo

21 f) Adjustments to the tube length may be required. To check this, move the cartridge holder left and right to each end of the printer. It shou

2211) Final touches (all models) a) Place the CISS unit on the left hand side of your printer and Insert all the air filters into the top of each a

2312) Refilling your CISS a) Do not allow the ink levels to fall below the refill line. To refill each ink simply remove the air filters and rep

2413) Priming a) Only prime your CISS if excess air (5cm or more) is present in the tubing. It is recommended that priming is conducted in a suit

25 e) Draw air into the syringe (DO NOT ATTACH A NEEDLE) then place it in the hole left by the removed travel plug. f) Push down

2614) Cartridge chip disable - Low ink. a) Flashing printer cartridges Your canon cartridges will flash when the chip thinks that ink is running

27 Warning message #2 Press Yes to continue. Warning Message #3 Press Yes to continue. Warning Message #4 Press and

28 15) Trouble Shooting Please contact rihactm on (+61)3 9005 5555 If any of the following trouble shooting suggestions do not fix your problems. D

29 d) Ink Tank Error. If your printer is stating that an ink tank error has occurred please check the following if the message does not identify the

3Installation Manual IP4200, IP5200, MP800, MP830 – 100ml Series Version 6-2009 Installation Manual ...

30 Does the printer still display ‘Ink tank errors have occurred’ on the screen? Re-click the cartridge back into position and repeat the steps in s

31 17) Canon Error Messages If one or more of your ink cartridges cannot be recognised, please ensure that the cartridg

32 Service error 5100 will occur if you have the silicone tubing fitted too tightly on your printer. Please check the tubing by follow steps 7)b) on

33

34 18) Warranty Please note that your CISS has a manufactures warranty of 3 months from date of purchase. Your warranty will be void if the system i

35

36 • CIS Systems • High Grade UV Dye Inks • Pigment Inks • Blank Media 157 Union Road, Ascot Vale, Vic 3032 Web: www

4

5Instruction Manual Canon Printers IP4200, IP5200, MP800, MP830 – 100ml Series Congratulations on your purchase of a rihac tm Continuous Ink Supply

6 b) After performing a head clean you must then perform Print Check Pattern. The computer will automatically ask you this, however if it doe

72) Preparing your new CISS for installation Please ensure the following are present with your CISS. (1) Air filters x5 (2) Silicone nozzle

83) Attaching Cartridge Chips – un chipped CISS unit only If you have purchased a pre chipped system please proceed to section 4) on page 10 Your o

9d) Examine the rear of the chip to ensure the LED has not been damaged or cut off. undamaged cartridge chip damage